VOLTAGE REGULATORS

For the devices to work properly, the electricity supplied to the device must be of a certain voltage. Efficient and smooth operation of the devices is a problem in areas where the mains voltage fluctuates too much. When electricity is not supplied as required voltage to the device, problems such as burning, distortion, production halting, data loss and failure occur in the devices. At this point, voltage regulators are used to solve all these problems. Voltage regulators that are connected after mains power before your sensitive devices regulate the voltage value and keep it within a certain range. The voltage regulator’s power is determined according to the current to be drawn by the total loads and the mains voltage value, allows you to use your devices and production lines safely. Voltage regulators are produced as standard or according to the input voltage range value you need.

Voltage regulators are divided into static and servo voltage stabilizers/regulators.

In servo voltage regulators, they contain moving parts called variants. Voltage regulation is provided by the movements of these variants. Static voltage regulators are regulated by electronic cards and microprocessor controlled thyristors.

Voltage regulators keep the voltage value within a certain range. That is, voltage regulators are used to keep the main voltage value within the desired range and protect the devices against voltage fluctuations. In a way, the task of voltage regulators is to protect your sensitive devices against any voltage changes.

For example, the devices used for manufacturing in factories are sensitive devices. While these sensitive devices are being produced, voltage variations are generally considered to be in the range of – / + 5%. However, in some regions, the voltage of the grid may decrease and increase at very high rates. In this case, voltage regulators are used to regulate by sensing the changes in the mains voltage and adjust to the level where the devices operate without stopping and deteriorating. In this way, in factories with large production capacity, both the devices work intact and production cannot be interrupted.

Servo voltage regulators
  • Regulation process is done through variants and motors
  • Microprocessor controlled technology
  • Independent operation between phases
  • Wide regulation range
  • Microprocessor controlled
  • Correction speed: 90V / second
  • Voice and visual warning system
  • High reliability
  • Suited with sensitive devices 
  • ISO 9001 standard production
  • Smart cooling with fan system
  • Ability to follow nonlinear loads
  • Protections: Over voltage, short circuit
  • Easy to use
  • Environmentally friendly 
  • Optional protection: over current, low voltage, phase protection, lightning protection / surge arrestor
  • Intelligent communication optionS
  • Truse RMS measurement 
  • High efficiency
  • Quiet operation
  • Audio and visual warning system
  • Manual by-pass option
  • 2 years warranty, 10 years spare parts warranty
  • Customized production
Static Voltage Regulators 
  • Regulation is provided with microprocessor controlled thyristors.
  • There are no moving parts in static regulators.
  • There is no dust accumulation between parts or wear does not occur over time.
  • Copper busbars is used
  • Perfect correction: 20 MHz – RISC
  • High reliability. Compatibility with sensitive devices
  • Correction phase response time: 20 milliseconds.
  • High speed correction: 500V / sec.
  • Zero Current Switching / Tap Changer Thyristor
  • Protections: High current, low voltage, high voltage, peak in mains current, short circuit
  • In case of high current, the semiconductor parts can withstand up to 10 times the rated current for 20 seconds.
  • EMI-RFI noise filter are standard for static voltage stabilizers
  • There is no distortion in static voltage regulators
  • Main spare parts are electronic cards and thyristors for static voltage regulators. That’s why, maintenance is very easy.
  • Productivity> 97%
  • When 110% is loaded, the allowed time is 10 minutes.
  • Quiet operation
  • Audio and visual warning system
  • Manual by-pass option
  • 2 years warranty, 10 years spare parts warranty
  • Customized production
  • ISO 9001 Standards production

We produce standard voltage regulators as indoor IP20 as well as special cabinet voltage regulators such as IP54, IP65 suitable for outdoor use.

Single phase 7.5-50kVA voltage regulators

Three phase 30-2000kVA voltage regulators according to project details

Usage fields of voltage regulators / voltage stabilizers: CNC machines, medical machines, computerized wood machines, processing, industrial, lazer cutting systems, printing houses, factories and to protect your whole house.